POWERNET 电源MSR 2400w
描述
2400 W 模块化电源系统
2400 W 模块化系统
每个模块的所有可用电压为 0…144VDC
U 和 I 从 0 到最大值可调
热插拔插件模块
电源或电池充电应用
用于远程监控的模块和电源警报
适用于重型应用的坚固结构
可选关断和输入过压
断开°C
POWERNET 电源MSR 2400w 系列
19” SUB-RACK UNITS | ||||
Type | Voltage versions | Modules per rack | Power | Mechanics (w x h x d) |
MSR7110/48 | 24V, 36V, 48V | 1…3 pcs | 800W…2400W | 19” (482mm) / 2U (88mm) / 360mm |
MSR7110/96 | 72V, 96V | 1…3 pcs | 800W…1800W | 19” (482mm) / 2U (88mm) / 360mm |
8871100C | Covering plate set for empty module place |
70130753 | IEC320 power cord 2.5m, rubber cable |
RECTIFIER MODULES | |||||||
Type | Input voltage *) | Nominal Output Voltage | Voltage Setting Range | Max Output Current | Current Limit Setting | Max Power | Mechanics (w x h x d) |
ADC7180R/24 | 55-264VAC/78-360VDC | 24 VDC | 0-36VDC | 30 A | 0-30A | 800W | 25TE / 2U / 230mm |
ADC7180R/36 | 55-264VAC/78-360VDC | 36 VDC | 0-54VDC | 20 A | 0-20A | 800W | 25TE / 2U / 230mm |
ADC7180R/48 | 55-264VAC/78-360VDC | 48 VDC | 0-72VDC | 15 A | 0-15A | 800W | 25TE / 2U / 230mm |
ADC7180R/72 | 55-264VAC/78-360VDC | 72 VDC | 0- 108VDC | 10 A | 0-10A | 800W | 25TE / 2U / 230mm |
ADC7180R/96 | 55-264VAC/78-360VDC | 96 VDC | 0- 144VDC | 7.5A | 0-7.5A | 800W | 25TE / 2U / 230mm |
*) Max power 600W at DC input
Reduced power 55…200VAC or 78…200VDC
INPUT
Input voltage | 55…264 VAC | 55…200VAC reduced power, see module datasheet |
78…360 VDC / max 600W | 78…200VDC reduced power, see module datasheet | |
Frequency | 45...65Hz | |
Safety | According to EN60950, Class I | |
Input current | Max 4.5A per module | |
Inrush current | Soft start | max 7A 10ms peak, otherwise less than 4.5A |
Isolation | Input / ground | 1500VAC |
Input / outputs | 3750VAC | |
Output / ground | 500VDC | |
Mains switch | Front panel with light | 12, 24, 48VDC One per PSU |
72, 96VDC One per sub-rack, max 10A current | ||
Mains input connector | Common input for each rectifier | IEC320 C14 male connector |
OUTPUT
Voltage Nominal voltages 0…144VDC / max 800W per module
Current Nominal current per module 0…30A / max 800W per module
Short circuit protection Rectifier modules Short circuit protected, electronic current limit
MCBs on front panel ADC7110/48 sub-rack 3 x 30A MCB in negative output
ADC7110/96 sub-rack 3 x 10A MCB in negative output
Output connector 3 terminal groups on rear panel 3-pole 10mm2 screw terminal for each rectifier
(+ , - , PE)
Hot swap Series diode in each rectifier Hot-swap allowed,
Input and output switch at OFF position Series/parallel operations All modules can be connected in series or in parallel
CONTROLS
Input On the front panel Power switch with ON/OFF light
Output On the front panel MCB ON/OFF safety switch
ALARMS
Input failure U in nom < appr. 150VAC Normally open and closed relay contacts Output failure Module failure or output switch off Relay contact and MCB auxiliary relay Alarm connector Rear panel Removable 12-pole 2.5mm2 screw terminal
Pin configurations
1 Mains alarm COMMON
2 Mains alarm NO
3 Mains alarm NC
4 Parallel output alarm COMMON
5 Parallel output alarm NO *)
6 Series output alarm PSU1 COMMON
7 Series output alarm PSU1 NC *)
8 Series output alarm PSU2 COMMON
9 Series output alarm PSU2 NC *)
10 Series output alarm PSU3 COMMON
11 Series output alarm PSU3 NC *)
12 Not in use
*) Normally = Mains / PSU OK
MECHANICAL
Power Rack Dimensions | 19” sub-rack Height | Positions for 3 pcs of ADC7180 euro modules 2U (88mm) |
Width | 19” (482mm) | |
Depth | 360mm | |
Weight | Rack without rectifiers | 5.5 kg |
Rectifier | 1.35kg | |
Enclosure | Steel | IP20 |
